View KK74VHC00_4156197.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TECHNICAL DATA
Quad 2-Input NAND Gate
KK74VHC00 is high-speed logic IC made by CMOS technology and designed for use in high-performance calculating systems with a wide supply voltage range. As for operation speed, KK74VHC00 can be compared with equivalent bipolar ICs based on Schottky TTL and two times surpasses ICs of KK74 series. KK74VHC00 tolerates operation under conditions when voltage on input is exceeded up to 7V without affecting characteristics and IC reliability. This possibility allows to use KK74VHC00 in radio-electronic devices for interfacing with supply voltages 5V and 3V, eliminate IC failure under supply voltage source emergency outage. Use of output edge shaping block in the microcircuit allows to reduce noise amplitude of noises when switching outputs into the same state simultaneously. Input and output levels of KK74VHC00 are compatible with CMOS levels
KK74VHC00
ORDERING INFORMATION KK74VHC00N Plastic KK74VHC00D SOIC TA = -40 to 85 C for all packages
Features: * Supply voltage range 2.0 to 5.5 V. * Output current 8 mA. * Low consumption current: 0.2 mkA (typical value) at = 25 . * Latchup current not less than 300 mA at = 85 . * Tolerable value of static potential not less than 2000 V as per human body model (HBM) and not less than 200 V as per machine model (). * Ambient operation temperature minus 40 to plus 85 . * Balanced signal propagation delay. * Ensures voltage exceeding mode on input * Low noise level at the simultaneous switching of outputs in the same state: VOLP = 0.8 V (max). * For pins and functions, compatible with KK7400. .
1
KK74VHC00
KK74VHC00 truth table
Input A B L L L H H L H H Note 1 - H - high voltage level; L - low voltage level; Output Y= A * B H H H L
Pinout
A1 01
B1 02
14
Vcc B4 A4
13
Y1 03
12
A2 04
11 Y4
10
09
08
B2 05
B3 A3 Y3
Y2 06
GND 07
Pins description in KK74VHC00
Pin No. 01 02 03
04 05 06
07 08
09 10 11
12 13 14
Symbol 1 1
Pin description
Input Input Output
Input Input Output
Common output Output
Input Input Output
Input Input Supply output from voltage source
Y1
2 2
Y2
GND
Y3
3 3
Y4
4 4 VCC
2
KK74VHC00
Absolute maximum conditions* Parameter, unit
Supply voltage, V Input voltage, V Output voltage, V Input diode current, mA Current of common output and supply output, mA Output current, mA Output diode current, mA Dissipated power, mW
Symbol min
VCC Vin Vout Iik Icc Iout Iok Pd -0.5 -0.5 -0.5 - - - - -
Value max
7.0 7.0 Vcc+0.5V -20 75 25 20 180
*Under absolute maximum conditions operation of microcircuit is not guaranteed. Operation is guaranteed under maximum conditions
Maximum conditions Parameter, unit Symbol min
Supply voltage, V Input voltage,V Output voltage, V Output current, mA Input rise and fall time, ns/V at Vcc = (3.3 0.3) V at Vcc = (5.0 0.5) V VCC Vin Vout Iout tLH, tHL 2.0 0 0 - 0 0
Value max
5.5 VCC VCC 8.0 100 20
3
KK74VHC00
DC electrical characteristics
Value Symbo l VIH Parameter High input voltage Test conditions - VCC, V 2.0 25 C min 1.5 max - - 0.5 0.3Vcc - - - - - - 0.09 0.09 0.09 0.09 0.36 0.36 0.25 0.1 4.0 -40 to 85 C min max 1.5 - 0.7Vcc - - 1.9 2.9 4.4 5.4 2.48 3.80 - - - - - - - 0.5 0.3Vcc - - - - - - 0.1 0.1 0.1 0.1 0.44 0.44 2.5 1.0 40.0 mkA Unit
V
3.0-5.5 0.7Vcc VIL Low input voltage - 2.0 3.0-5.5 2.0 3.0 4.5 5.5 3.0 4.5 2.0 3.0 4.5 5.5 - - 1.92 2.92 4.42 5.52 2.58 3.94 - - - - - - -
VOH High output voltage
VI = VIH or VIL IO = -50 mkA
VOL
Low output voltage
VI = VIH or VIL; IO = -4 mA VI = VIH or VIL; IO = -8 mA VI = VIH orVIL IO = 50 mkA
IOZ II ICC
VI = VIH or VIL 3.0 IO = 4 mA VI = VIH or VIL 4.5 IO = 8 mA Output current in VI = VIH or VIL 5.5 VO = VCC or 0V "off" state Input current VI = 5.5V or 0V 0 - 5.5 Consumption current VI =VCC or 0V 5.5
4
KK74VHC00
AC electrical characteristics (tLH = tHL = 3.0 ns)
Symbol tPHL, tPLH Parameter Test conditi VCC, V ons Value CL, pF 15 50 15 50 -40 to 85 C min max min max 7.9 9.5 11.4 13.0 5.5 6.5 7.5 8.5 10 38 25 C Unit ns
Propagation delay time Figure 3.3 0.3 when switching "on", 2 "off" 5.0 0.5 Input capacity Dynamic capacity VI = 0 V orVCC 5.0 5.0
CI CD
pF
Noise characteristics (CL = 50 pF)
Parameter Symbol VOLP VOLV VIHD VILD VCC, V Positive noise of low output voltage 5.0 Negative noise of low output 5.0 voltage Input dynamic high voltage Input dynamic low voltage 5.0 5.0 min -0.8 3.5 Value max 0.8 1.5 Unit V
5
KK74VHC00
- Time diagram of input and output pulses
tLH 0.9 A, B 0.5 0.1 tPLH tHL 0.9 0.5 0.1 tPHL VCC Y 0.5 0.5 0V GND V
6
KK74VHC00
N SUFFIX PLASTIC DIP (MS - 001AA)
A 14 8 B 1 7
Dimension, mm Symbol A B C MIN 18.67 6.1 MAX 19.69 7.11 5.33 0.36 1.14 2.54 7.62 0 2.92 7.62 0.2 0.38 10 3.81 8.26 0.36 0.56 1.78
F
L
D F
C -T- SEATING N G D 0.25 (0.010) M T K
PLANE
G H
H J
M
J K L M N
NOTES: 1. Dimensions "A", "B" do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side.
D SUFFIX SOIC (MS - 012AB) Dimension, mm
8
A 14
Symbol A
MIN 8.55 3.8 1.35 0.33 0.4 1.27 5.27 0 0.1 0.19 5.8 0.25
MAX 8.75 4 1.75 0.51 1.27
H
B
P
B C
1
G
7 C R x 45
D F G
-TD 0.25 (0.010) M T C M K
SEATING PLANE
H
J F M
J K M P R
8 0.25 0.25 6.2 0.5
NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B 0.25 mm (0.010) per side.
7

▲Up To Search▲

Price & Availability of KK74VHC00

	To Download KK74VHC00 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .